Pages

Tuesday, June 5, 2012

Making Moccasins! With full How-To...

MOCCASINS DIY..



The Cast:

  • A Wife
  • A Husband



The Scene:

  • A Livingroom, Sunday evening. The wife is spread out on the sofa, the TV is running, but she doesn't seem to be paying attention to the program at all. She has a bit of a blank expression on her face. The floor is completely littered with all kinds of tools and leather scraps, paper, string and needles. We hear somebody enter a door off-stage, her face lights up, but she barely moves. The living room door opens and the husband sticks his head in.

THE HUSBAND: Hi! 

THE WIFE: Hubby! Got your work-Sunday over with well?

THE HUSBAND: Yes, long, but fine. And you? What did you do all day?

THE WIFE: I made shoes.

THE HUSBAND: What do you mean, you made shoes?

THE WIFE: The ones I'm wearing right now. I just made them.

THE HUSBAND: What? No way! Really?! (He is truly impressed, but along with that, there is also a slight undertone of excitement about the fact that she might stop spending so much money on shoes in the future...)




Sorry if I'm making a big drama out of this, but I've been wanting to make street-shoes for such a long time, and I finally did, and they turned out really pleasing. So bear with me, ok? :-)

Some of you might remember my earlier tries at making shoes. I have always meant to get back to it, and my mind has been pre-occupied with it a lot. HERE is a first post on making shoes, and a second one HERE with a how-to for braided shoe soles.
Since the last shoe-post I have been hunting for materials and - much more difficult - literature on the subject. One of my lasts still has the same half-shoe attached to it as almost a year ago: 



Trouble is: I'd need a heel. Heels are difficult to get, make and attach. So I'm stuck. I finally decided I needed to start smaller. And that's where the moccasins come in.

HERE'S HOW TO MAKE THEM:

By the way, I made them in one single day. You should probably do this first step one day in advance though, so the leather can dry again...

First you need a fairly thick leather for the soles. I found mine at a flea market, it is not a good quality, but for my first tries it will do. It has stains and all. It's about 3mm (1/8 inch) thick. A little thicker would be better.
Cut out a very rough outline of your foot and soak it in water. This will make it a lot softer and easier to cut out precisely afterwards. Also cut some pieces for the heels and soak them as well. 


Draw the outline of your foot on a piece of paper, making sure you are always holding the pencil perpendicular to the paper.
Then draw the outline of your sole based on your foot. You can take away some width at the instep, as you see in the picture below.
Draw a line through the center of your heel and through approximately your second toe. Then draw a line square to the first line, at the height where you'll want your flap:


Now step onto your drawing with a string under your foot. Hold the string over your foot and mark where you'll want the sides of your shoes to go to:


Then you lay the string out flat and transfer the mark to the paper pattern. Do that in several places and connect the dots. Mine came out this way (the slight curve at the height of the ankle had to be corrected and smoothed out later):


Cut it out and "try it on". In my case I decided to add some length to the heel part, just to be on the safe side. It was shortened again later:


This is your main pattern piece. Cut out your upper leather (I found a big box of leather scraps in different colors on Ebay...). I used a regular crafting knife. A rotary cutter works brilliantly too, but don't use the same one you want to use for fabric again later... Always remember to cut one left and one right side...


Transfer the pattern for the sole onto a separate piece of paper and cut out. Now use the soaked leather for the soles and cut two soles and several heel-parts (I used three per shoe).


Use sandpaper to make the surfaces of the leather rough. It will be holding together so much better that way!


Use great glue. Glue made for shoes and leather. Read the package. Mine had to be applied to both surfaces, then let dry for about 15 minutes, then glued together and hammered. Not how long you hold it together, but how hard you hammer will decided how well it will be glued!
Glue the heel pieces together, and glue the soles to the outside of your upper leather. Be careful with the correct placement, it is crucial to get it right:


Now I used a hole-puncher and sewed the soles to the upper leather. Using a leather needle would actually be better, as the shoes would then stay water-proof. Leather "mends" again after going through it with a needle and closes up entirely. Obviously that isn't the case if you make holes. My leather needle has a very small eye though, no way I could have fit a big enough string through it.
Use heavy duty string. Ideally, you would wax it, too. Mine is special string for shoe-making...


Next I cut out an inner sole, transferring my pattern to store-bought insoles, which I then wrapped in fabric. I only laid them into the shoes, but you could glue them if necessary:



Punch the holes around the toe-part of the upper. Mine are 1 cm apart (3/8 inch). It has to be an even number of holes, so the string doesn't go in at the bottom and come out on top...


Pull a string through and put on your shoe. If you had made the sides higher than me, they could be worn like this as sandals. I wanted to make a flap though. Stick a piece of paper in place of the flap and draw the pattern, marking the holes and calculating in the extra "seam allowance" needed...


This is what my pattern piece looked like. I had drawn the line with the little marks while wearing the shoe, then I drew in the dots afterwards - that is where the holes really had to be:


After taking the string back out and attaching the flap, you adjust the back. Hold it tightly to your foot and mark a line through the center of your heel.


Roughly sew together the two side parts, which you have cut back to the line. Then with nicer stitches attach the heel flap over it. I did this with a leather needle, not by punching holes. If it is long, you could even fold it over to the inside. I didn't, as I was going to put another leather stripe over that edge anyway:



The shoes are basically done now and could be worn. I added some fringe to the front and enhanced the side edge with another stripe of leather. Both pattern pieces were made while wearing the shoes and holding/folding paper to them. In the photo below you see what they looked like (the fringe-piece is already torn apart a bit...). You also see how I attached the leather stripe with paperclips first, then punched the holes through all three layers at once before pulling the string through:


Finally I used a dremel to smooth out the heel-sides. Be careful not to touch the outer leather of the shoe though:


From the bottom:


Ta-daaaaaaaaaaaaaaa!!!!!!!!!!


I have to buy some rubber soles to protect the leather and make sure the seam doesn't get torn from the asphalt. In the meantime, I cut a cabinet-drawer-non-slip-inset-mat-thingy to the shape of the soles and glued it. It was still wet in the picture and doesn't look nice, but at least I can go try out these shoes on the street now! :-)


They are AMAZINGLY comfortable. After all, they have been custom-made for my feet. I will never take them off again. Maybe for sleeping and taking showers. Other than that, I don't think so...

Here is the overview of all the pattern pieces that were needed...


The pattern can be varied endlessly, making no flaps but higher sides, making the flap higher etc, etc...


Of course you could go wild with beading and embroidery...


By the way, welcome all my new readers! I am thrilled to have you aboard and I hope to keep delivering interesting posts. As you see, sometimes there is a long time between them, but I'd rather have a lot of content than a lot of posts.
My near-future projects are on more shoe-making, as well as recycling clothes, coming up with my own patterns for new clothes and the vintage dress I am about to finally start (the blue one with the jacket in the picture below...). Also, I keep working on my fashion illustration skills, so hopefully some posts on that are going to follow sometime soon, too.


Have a grand week - see you soon with a free pattern!
Best,
Katja

22 comments:

  1. Wow, how nice is that! I've to try this. Thank you for the tutorial, it looks so cute!

    ReplyDelete
  2. Wow!  Those are adorable, and comfortable too... double score!  

    ReplyDelete
  3. Well done!  These look great!  My Grandfather was a shoe-maker  back in his day, and I remember the heart & soul he put into everything he made.   Having a great fit is soo important to your feet. Who wants sore tootsies anyhow?   I've been making slippers with great inserts and now think I should bump it up to making some shoes.
    Inspirational.
    Thanks for sharing .

    ReplyDelete
  4. I am very interested in making shoes.  I even purchased a $30 book on shoe making.  The book suggests using heels from shoes you get at yard sales etc. that are not worn.  Anyone else interested in making shoes of all kinds I would love to hear from you.  I have a daughter that we cannot find shoes that fit at any price due to some feet imperfections and that one foot is a size larger than the other.  susansmiles61@yahoo.com

    ReplyDelete
  5. Hi Susan and thanks for your comment! Congrats on buying the books - I have found several ones now and I will definitely post more on making shoes. Thanks for the input - I also had that idea of buying cheap second hand shoes and re-using the heels, and I will definitely do that. Good luck with your own projects! Hope to hear from you again!

    ReplyDelete
  6. Thank you! Yes, I think it comes with the craft - you have to put heart and soul into it, it will turn out twice as nice... I hope you were able to save some of your Grandpas tools and literature... All the best to you!

    ReplyDelete
  7. krass. das sieht nach ner heidenarbeit aus! respekt :)

    ich mache im moment eine blogvorstellungs-aktion. vielleicht hast du ja lust mitzumachen :)
    http://www.strangenessandcharms.blogspot.de/2012/05/win-blog-presentation.html

    lg
    dahi
     

    ReplyDelete
  8. Wow!!!  I am in awe of your creativity and skills.  They look great!!!

    ReplyDelete
  9. This is fascinating.  Thank you for the detail.
    My partner does leather working so I will show him this!

    ReplyDelete
  10. Totally awesome! And you're loaded with skill!

    ReplyDelete
  11. Thanks for this great tutorial! You seemed to go above and beyond what I have seen before with mocassins. They are stylin' and look very comfy!

    ReplyDelete
  12. I love this tutorial I just bought a moccasins pattern, but it came with no instructions :( now atleast I have an idea how to go about it thank you!
    did you ever get rubber sole? what did you use?
    thanks

    ReplyDelete
  13. Hi! Sorry for the late answer... I still have that rubber stuff on it - it's a mat that you are meant to put in your kitchen drawer so the pots and pans don't slide around in it. It works pretty well so far, but I have been wearing them inside mainly. Somebody gave me the tip to buy old tires and cut soles from them, but I haven't tried it yet... Good luck with yours!

    ReplyDelete
  14. This is the coolest ever! You have inspired me to try again at making shoes!

    ReplyDelete
  15. when you are doing the measurements with the string and then the transferring, are you just rotating the string( spinning them in opposite directions), or are you sliding the string up the length of your foot?

    ReplyDelete
  16. I'm sorry I am seeing this so late! If I understand the question correctly, you slide the string up under your foot, so the string always lies in a straight line when you transfer it to the pattern...

    ReplyDelete
  17. I'm so going to make these! Though I plan on lining mine with rabbit fur, and using a canvas instead of leather (I don't have the money for leather). Moccasin slippers! :) (with a thick leather sole, of course).

    ReplyDelete
  18. Oh that sounds great! Be sure to share a link to them if you want to - I love seeing results from my tutorials ;-)

    ReplyDelete
  19. These are darling! I've been looking for a simple startup to making footwear, and this looks like just the thing. I love projects that can be cranked out in a day, but still look super impressive :) Thanks for the fabulous tutorial!

    ReplyDelete
  20. can u scan these pattern and put here for us? great tutorial thank you?

    ReplyDelete
  21. Good job. That's absolutely awesome, I expect to see a business

    ReplyDelete